Understand what has actually failed

“Inert gas failed” can describe very different casualties:

- loss of inert-gas generation; - blower or power failure; - damaged supply main or branch line; - deck-seal or non-return failure; - valve actuator or control-air loss; - unreliable pressure, oxygen or gas measurement; - damage to a tank boundary or vent system; or - contamination or backflow toward machinery spaces.

Identify alarms, pressure trends, oxygen readings, valve positions and visible damage from safe locations. Compare fixed instruments with calibrated portable equipment where approved procedures allow.

A displayed normal pressure is not proof of integrity if the sensing line is damaged. One acceptable sample does not prove that all parts of a tank atmosphere are non-flammable. Record the sampling point, method, time and instrument status.

The FSS Code defines the inert-gas system broadly to include the plant, distribution, backflow prevention, measuring instruments and controls. Restoration of one component does not restore the whole safety function.

Stop operations that draw air into tanks

The FSS Code requires covered cargo tanks to be maintained with oxygen content not exceeding 8% by volume and at positive pressure, except when gas-freeing is necessary. The system is intended to prevent air entering during normal operations.

If the system cannot meet its operating requirements, stop cargo discharge, deballasting of cargo tanks and tank cleaning in accordance with the applicable procedures. These activities can draw atmosphere into tanks or change pressure.

Secure pumps and valves in a controlled manner. Coordinate with the terminal before an emergency shutdown creates pressure surge or line problems. Confirm manifold and shore status.

Do not resume merely because delay is expensive. Historical IMO requirements allow specified emergency conditions for certain operations when repair is impracticable, but these are not a general waiver. The ship, flag, class and terminal need the actual system condition, cargo and applicable requirements.

Charterers cannot authorize operation of a defective statutory safety system.

Control every potential ignition source

A damaged inert-gas system makes ignition control more important. Enforce the ship's cargo and fire precautions. Stop non-essential hot work and electrical activity in affected zones. Control portable equipment, vehicles, smoking and access.

A projectile strike can itself leave hot surfaces, arcing cables and smouldering insulation. Thermal imaging or remote inspection may help identify heat without exposing personnel. Fire watch and atmosphere monitoring should focus on damage paths as well as routine cargo locations.

Do not open tank hatches to “let pressure out” or inspect directly. That can admit air, release vapour and expose personnel. Use the designed venting and sampling arrangements under approved procedures.

Nitrogen and inert gas also create oxygen-deficiency hazards. Keep people away from outlets and suspected gas accumulation. No entry into tanks, voids or connected spaces without the enclosed-space procedure, atmosphere testing, authorization and rescue readiness.

Maintain pressure without overpressurizing

Positive pressure helps prevent air ingress, but damaged tanks and piping may have reduced pressure tolerance. Feeding gas into an unknown leak can release flammable or toxic vapour elsewhere.

Monitor tank pressure and vent operation. Identify whether pressure loss is system consumption, temperature change, leakage or boundary damage. Compare tanks rather than assuming a fleet-wide instrument value.

If an alternative inert-gas source is considered, verify compatibility, capacity, quality, connection and backflow protection. A portable nitrogen supply can introduce extreme asphyxiation risk and may not distribute gas as assumed.

Do not bypass alarms, seals or non-return devices without an engineered, authorized procedure. Temporary arrangements need drawings, limits, monitoring and a defined removal plan.

Any tank pressure action must be coordinated with structural, cargo and fire assessments.

Sampling must be representative and safe

Use approved sampling points and calibrated instruments. Verify oxygen measurement and, where relevant, hydrocarbon concentration, toxicity and pressure. Follow instrument limitations and correction requirements.

Create a table by tank and time:

- pressure; - oxygen reading; - hydrocarbon or other required reading; - sample location; - instrument identifier; - temperature; - confidence or anomaly; and - action taken.

Trend matters. A tank rising from 4% to 7% oxygen may still be below the 8% limit at that sample but moving toward loss of control. Another tank with a stable reading may have an isolated branch.

Personnel should not lean over vents or enter vapour clouds to improve a reading. Remote or fixed information may be less complete but safer until the area is secured.

Where fixed and portable results disagree, treat the atmosphere as uncertain and investigate the instruments and sample path.

Repair requires gas and mechanical discipline

Before work, isolate energy and cargo hazards. Determine whether the damaged component contains flammable vapour, inert gas under pressure, hot surfaces or chemical residues. Establish permits, gas testing, firefighting readiness and communications.

A strike may have misaligned piping or supports beyond the obvious hole. Inspect the wider route and non-return protection. A patch that holds static pressure may fail under vibration or flow.

After repair, test leakage, valve action, alarms, trips, oxygen quality, pressure control and backflow prevention according to approved procedures. Confirm distribution to each affected tank.

Class, flag and manufacturer involvement may be required. Record temporary repairs and operating restrictions. The system's statutory and survey status cannot be inferred from a successful restart.

A competent authority may require permanent repair before cargo work or departure.

The terminal needs a verified interface decision

Ship and shore should exchange the defect, cargo condition, shutdown status and proposed test or repair. The terminal must evaluate its own emergency and vapour-control systems.

Do not conceal an inert-gas defect to avoid losing a berth. If operations stopped at sea before arrival, disclose the limitations early enough for the terminal to decide whether it can accept the vessel.

Agree who may authorize each step, including connection, testing, inerting, discharge and disconnection. Record the decision and conditions.

If shore-supplied inert gas or nitrogen is considered, use an engineered interface with pressure, quality, capacity, isolation and emergency shutdown controls. A hose connection and verbal assurance are not a safety case.

Pilots and tugs may also need relevant hazard information without receiving unnecessary security detail.

Commercial consequences follow the safety decision

Loss of inert gas can delay discharge, require deviation, trigger repairs and affect cargo quality or delivery. It may generate off-hire, laytime, deviation and insurance questions.

Issue factual notices stating the system function lost, operations affected, actions underway and next update. Do not announce an expected restart before testing and approvals are defined.

Notify hull and machinery, P&I and war-risk insurers as applicable. Preserve alarms, trends, maintenance, calibration, damage photographs, VDR material, terminal communications and expert advice.

Causation may involve hostile damage, pre-existing defect or both. Separate the verified strike damage from later technical findings.

The financial urgency of a demurrage clock does not change flammability physics.

A controlled scenario

A crude tanker sustains fragment damage to the inert-gas deck main while approaching a terminal. Tank pressures begin falling, and one fixed oxygen channel becomes unreliable.

The master stops cargo preparation, controls ignition sources and informs the terminal. The crew uses approved points and portable instruments to trend each tank without entering the damaged area. Class and technical advisers assess the main, deck seal and supports. A temporary repair is pressure- and function-tested before any authority considers resumed operation.

This is a hypothetical training scenario, not a report of a specific ship or forecast.

Commercial conclusion

Restoring inert gas means restoring a safety function, not producing one favourable number. Generation, distribution, isolation, measurement, pressure and backflow prevention all matter.

Owners should keep ship-specific failure procedures and emergency technical contacts. Masters need authority to stop cargo operations. Terminals and charterers need early disclosure and disciplined expectations. Insurers need the unedited alarm and repair chronology.

ZeaClub can track tank trends, defect status, approvals, notices and evidence. It cannot certify an atmosphere, approve a temporary repair or authorize cargo operations.

This article distinguishes verified source material from ZeaClub analysis, recommendations, forecasts and hypothetical scenarios.

Sources