Establish where water is entering and going
Determine the suspected breach location, affected spaces, water depth or level trend, sea connection and access limitations. Use remote sensors, bilge alarms, tank soundings, CCTV and safe observations.
Build a compartment table with:
- confirmed, suspected and dry spaces; - water level and time; - inflow or rise rate; - pumps and suction available; - doors, hatches, valves and vents; - connected pipes, ducts and trunks; - fire, electrical or cargo hazards; and - confidence in each report.
A dry sensor does not prove a dry compartment if power or signal cable is damaged. A stable level can mean equilibrium with the sea, not that ingress has stopped.
Mark the ship's draft, trim and list at regular intervals using more than one source where possible. Record weather, heading and motion because they affect breach immersion and water movement.
Do not send people into a flooded, contaminated or structurally uncertain space merely to improve the table.
Close the paths before chasing the water
Progressive flooding can pass through an open watertight door, damaged pipe, ventilation duct or cable penetration. The IMO damage-control framework emphasizes maintaining subdivision boundaries and preventing spread through openings.
Verify closure status locally where safe. Bridge indicators can be wrong after power or cable damage. Check remote valves, cross-flooding arrangements, sounding caps, manholes, access hatches and ventilation closures against the damage plan.
Do not close a path blindly if it traps people, blocks essential escape, disables needed machinery ventilation or causes dangerous pressure. Account for personnel first and coordinate changes.
A weathertight closure is not automatically watertight. IMO instruments distinguish weathertight protection against sea penetration from watertight resistance to pressure in either direction. Use equipment only for its designed function.
Temporary blankets, wedges or patches may reduce flow, but they do not convert a damaged boundary into an approved watertight structure.
Compare inflow with pumping honestly
Pump capacity on a drawing is not delivered capacity in a casualty. Suction height, debris, power, hose routing, list, air leakage and damaged valves reduce performance.
Measure level change before and after each pump starts. Confirm where discharge goes and that it does not re-enter the ship or create pollution and personnel hazards. Keep strainers and suction points monitored.
Portable pumps add fuel, exhaust, electrical and hose risks. Locate them safely and preserve access. A pump that requires a crew member to remain in a deteriorating compartment is not a sustainable control.
If water level still rises, report the net trend and estimated time to critical boundaries. Do not say “pumps coping” merely because they are running.
Prioritize containment and inflow reduction. Pumping an unlimited sea connection without isolating it can buy time, but it is not repair.
Stability calculations need casualty inputs
The intact loading computer may not model the actual breach, free communication with the sea, damaged permeability or progressive paths. Use the damage-control information and seek naval-architecture, class and salvage support.
Provide:
- loading condition and tank states before impact; - affected and adjacent compartments; - observed levels and trends; - draft, list and trim history; - open or compromised boundaries; - cargo, ballast and bunker changes; - firewater accumulation; - weather and sea; and - proposed pumping or transfer actions.
State which values are measured and estimated. A remote analyst cannot improve a false input by adding decimal places.
The analysis should address residual stability, downflooding points, hull-girder strength, allowable actions and trigger thresholds. The fact that the vessel remains upright is not a stability calculation.
Recalculate when flooding, pumping, weather or configuration changes materially.
Do not counter-flood by instinct
Moving ballast or cargo can reduce list while worsening stability, longitudinal strength, tank pressure or pollution risk. Counter-flooding deliberately sacrifices buoyancy and can create additional free surface.
Before transfer, define the objective, source, destination, quantity, rate and stop condition. Check the receiving tank's capacity and integrity. Identify the effect on draft, trim, bending moment, shear force and damaged structure.
A visually level ship can be less safe than a controlled list. Do not chase zero degrees without technical advice.
If cross-flooding arrangements are designed into the ship, use them according to approved information and confirm their actual status. Improvised opening of boundaries is not equivalent.
Charterers and cargo interests may supply loading data, but they should not direct an emergency transfer.
Temporary repairs require a test and limits
Options can include soft patches, collision mats, shores, plugs, welded or bolted structures and external assistance. Selection depends on breach geometry, pressure, material, access, fire, cargo and sea conditions.
Assess the area for unexploded ordnance, electrical hazards, toxic atmosphere and structural instability before work. Protect repair teams with communications, escape routes and monitoring.
A repair plan should specify:
1. design and load assumption; 2. materials and installation sequence; 3. isolation and personnel controls; 4. test method; 5. inspection frequency; 6. operating limits; and 7. failure contingency.
Reducing visible leakage is an operational result, not class approval. Monitor deformation, seepage and adjacent structure as draft and motion change.
Class, flag and coastal authorities may require survey, restrictions or permanent repair before sailing. Preserve drawings, photographs, material details and test records.
Treat structural damage as wider than the hole
Blast loads can crack welds, distort frames, damage coatings and misalign doors or piping beyond the visible breach. Fire can reduce material strength. Fragment paths may connect several spaces.
Inspect adjacent structure remotely or through qualified survey where safe. Track unusual sounds, vibration, paint cracking, buckling, leakage and changing alignment.
The SOLAS goal-based standards for large oil tankers and bulk carriers emphasize strength, integrity and stability in intact and specified damage conditions. An actual hostile strike may fall outside design assumptions and requires case-specific engineering.
Do not remove debris or straighten structure before competent inspection unless needed for immediate safety. Document any unavoidable change.
Cargo containment and pollution risk need their own assessment, even if seawater ingress is controlled.
Organize one flooding command picture
The master should receive a concise board showing compartment state, boundaries, pumps, draft, list, technical limits and next trigger. One officer should control updates and reconcile conflicting reports.
The company can coordinate naval architects, class, flag, salvor and insurers. It should send one consolidated advice package to the ship. Mark assumptions and approval status.
Notify coastal and pollution authorities as required. Preserve logs, alarms, soundings, loading-computer states, valve actions, pump times, transfers and communications.
Separate facts from models. “No rise for 20 minutes with two pumps running” is a fact. “Breach sealed” is a conclusion that requires more evidence.
Crew fatigue matters. Flooding control may continue for days, so establish watch rotation and relief before errors accumulate.
A controlled scenario
A bulk carrier receives a strike near a side ballast tank. Water appears in an adjacent void, and list slowly increases. One remote door indicator remains green although local communications are lost.
The master treats the adjacent space as suspect, closes connected systems, verifies accessible boundaries and trends levels. Pumps slow but do not stop the rise. A naval architect models the actual loading condition before any ballast transfer. A temporary patch is installed and tested, then monitored during a low-speed trial with tug support.
This is a hypothetical training scenario, not a report of a specific casualty or prediction.
Commercial conclusion
Progressive flooding is a network problem. The breach, openings, pipes, pumps, stability, strength and ship motion interact.
Owners should maintain accurate damage-control information and 24-hour naval-architecture support. Masters need authority to preserve boundaries and reject premature movement. Charterers and cargo interests should provide data without directing transfers. Insurers and salvors need measured trends and repair evidence.
ZeaClub can track compartments, levels, boundaries, calculations, approvals and action owners. It cannot calculate residual stability, approve a patch or certify the ship fit for sea.
This article distinguishes verified source material from ZeaClub analysis, recommendations, forecasts and hypothetical scenarios.
Sources
- International Maritime Organization, Ship design and stabilityAccessed 2026-11-19
- International Maritime Organization, SOLAS Convention overviewAccessed 2026-11-19
- IMO Resolution MSC.429(98), explanatory notes on subdivision and damage stabilityAccessed 2026-11-19
- IMO Resolution MSC.235(82), damage stability provisionsAccessed 2026-11-19
- IMO Resolution MSC.143(77), Load Lines Protocol amendmentsAccessed 2026-11-19
- International Maritime Organization, Surveys, verifications and certificationAccessed 2026-11-19